Glass floor 40 mm

Tempered-laminated glass, clear color, thickness 40 mm, custom made

(more information)
Art. no.
301254
€1,017.00
per m²
Delivery: 3 - 4 working weeks
  • Free shipment from € 500,- (incl. VAT)
  • Pick-up in NL or delivery in NL and Flanders (exception of the Wadden Islands)
  • Relatively short delivery times
  • Pay with i.e. iDeal, Riverty, Billink, Bancontact, PayPal en Creditcard

Glass floor 40 mm is tempered laminated glass that consists of three tempered glass plates, each 12 mm thick, that are connected with several transparent PVB foils. There are a total of 8 foils, each 0.38 mm thick. By toughening the glass, the glass becomes 4 to 5 times stronger than untempered glass. And the foil ensures that the glass remains attached to the foil in the event of glass breakage and that no opening is created in the glass. This makes it suitable for situations where this extra strength is necessary and fall-through safety is necessary.

Safety requirements apply to the application of the correct glass type and thickness. Read the explanatory notes below

 

Features of glass floor 40 mm:

tick-marks  Tempered-laminated glass with transparent foils
tick-marks  Transparent clear glass
tick-marks  Consisting of 3 tempered glass plates of 12 mm, with 2x 4 transparent foils in between, each 0.38 mm thick
tick-marks  Standard polished edge finish
tick-marks  Do not allow UV radiation to pass through
tick-marks  Suitable for indoor and outdoor application
tick-marks  If applied outside: delamination is always outside the warranty. This is strictly handled by the glass manufacturers
tick-marks  This glass weighs 90 kg per m²
tick-marks  The mentioned price is a m² price
tick-marks  Can be custom-made in the glass configurator

 

Glass floor 40 mm is provided by us:

tick-marks  Custom made
tick-marks  Delivered according to specified specification (note! For glass production tolerances apply!)
tick-marks  Delivered at delivery address. Pick-up is also possible, the options are mentioned on the payment page

 

Points of attention for glass floor 40 mm:

tick-marks  Tempered-laminated glass can be used outdoors, however, if the edges of the glass are exposed to moisture for a long time, there is a real risk of delamination of the glass (release of and / or air bubbles between the glass plates, at the edges of the glass). This can result in the transparent film becoming white in these places over time. Delamination is inherent in the long-term exposure of moisture on the end face of laminated glass and is always out of warranty. This applies not only to us but to all factories and companies that supply laminated glass. It is not a production error, but a product specification that is warned about
tick-marks  Once the glass has been tempered in the oven you can not adjust it. The glass plate will break with every attempt you try to change it. It is therefore very important that you order the correct glass size and with all needed additions in it (such as drill holes). You can no longer add this once the glass has tempered
tick-marks  You are responsible at all times for applying the safety standards and requirements applicable in your country! In the Netherlands, this includes NEN-3569:2011 (“Vlakglas voor gebouwen – Risicobeperking van lichamelijk letsel door brekend en vallend glas – Eisen” voor Nederland).
tick-marks  For the production of custom glass, tolerances have been determined within the glass industry in terms of dimensions, quality and finish. These are industry-wide and are used by all glass companies. Please note that it is possible that glass may have a small size deviation (approx. 1 - 2 mm), and certain miniscule damages cannot always be claimed
tick-marks  Think carefully about the right glass size. Size changes are no longer possible once your order has gone into production
tick-marks  Think carefully about the correct glass thickness. We cannot take any responsibility for incorrectly applied and/or mounted glass. Get advice from a structural engineer or architect
tick-marks  Within the glass industry it is customary to calculate a minimum area per piece. This is necessary because the handling of an order is always necessary and this prevents a glass plate from costing € 1.50, for example, while the actual production costs are much higher. The minimum area to be calculated differs per product and is stated under the tab "More information" on the product page